Trying again Payne 201 taper - Reed Guice
This is a multi-part message in MIME format.
--===============1625688617==
Content-Type: multipart/alternative;
boundary="----=_NextPart_000_00F5_01C889DF.5E1313C0"
This is a multi-part message in MIME format.
------=_NextPart_000_00F5_01C889DF.5E1313C0
Content-Type: text/plain;
charset="us-ascii"
Content-Transfer-Encoding: 7bit
The numbers messed up last post. Here's another try.
Reed
_____
From: Sydney A. Smith [mailto:]
Sent: Wednesday, March 19, 2008 5:01 PM
To: 'Reed Guice'
Subject: RE: [RODMAKERS] Payne 201 taper
Reed - As you can see there are a lot of tapers attributed to Payne's 201.
IT IS TWEAKED. Here is the taper for the rod I made. 8 foot, 3 piece.
Measurements are on the UNVARNISHED sections:
Butt (inches) Mid (inches) Tip
Ferrules 16 and 11 - Super Z - with step down at ferrules as shown
0 - .355 0 - .242 0 -
.158
5 - .355 5 - .2355 5 -
.146
10 - .355 10 - .2255 10 -
.135
15 - .304 15 - .215 15 -
.123
20 - .285 ` 20 - .202 20 -
.111
25 - .271 25 - .191 25 -
.093
30 - 257 30 - .1755 30 -
.071
32 - .254 32 - .171 32 -
.067
Measurements on the VARNISHED/FINISHED rod from tip down: measured as close
to the inch indicated as possible given ferrules and guide wraps, but
clearly not as accurate as above.
0 - .067
5 - .078 Dipped: 4 coats butt , 4 coats mid,
3 coats tips.
10 -.103
15 -.118
20 - .134
25 - .143
30 - .150
35 - .180
40 - .194
45 - .205
50 - .219
55 - .228
60 - .238
65 - ferrule
70 - .274
75 - .286
80 - .296 (begin swell)
85 - .352 (swell)
90 - grip
95 - grip
96 - grip
Sydney A. Smith
_____
From: Reed Guice [mailto:]
Sent: Wednesday, March 19, 2008 9:50 AM
To: 'Sydney A. Smith'
Subject: FW: [RODMAKERS] Payne 201 taper
_____
From: [mailto:rodmakers-bounces@goldrush.com]
On Behalf Of Steve Weiss
Sent: Thursday, March 13, 2008 11:22 AM
To: Rodmakers List
Subject: Re: [RODMAKERS] Payne 201 taper
Paul, and others,
This taper was very popular at last year's CRR. One of the favorites in
the rod evaluation event. This rod gets a lot of use.
Payne 201, 8', 5/6-wt, 3/2
The original that I took the taper from was made by Payne for Abercrombie &
Fitch, NY.
I Measured three flats and averaged them, then took .006 off for varnish.
Here are the measurements for the rod with the tip I used.
1 .056
5 .0725
10 .090
15 .098
20 .112
25 .130
30 .146
31 .147
35 .158
40 .176
45 .193
50 .208
55 .218
60 .226
62 .229
64 .234 (interpolated)
65 .248 (interpolated)
67 .246
70 .254
75 .271
80 .282
85 .306
86 .3325
.340 to the end of the butt
I glued the rod with resorcinol.
The original has stepped ferrules, so I used CSE stepped ferrules.
There are 10 snakes plus the stripper. The guide spacing from the tiptop is:
4 5/8, 9 3/4, 15, 20 3/8, 25 7/8, 34 (against the female ferrule), 40 1/4,
47 11/16, 56 3/4, 66 5/16 (against the female ferrule), 74 5/8
(Stripper).-----
Steve
No virus found in this incoming message.
Checked by AVG.
Version: 7.5.519 / Virus Database: 269.21.7/1335 - Release Date: 3/19/2008
9:54 AM
No virus found in this outgoing message.
Checked by AVG.
Version: 7.5.519 / Virus Database: 269.21.7/1335 - Release Date: 3/19/2008
9:54 AM
------=_NextPart_000_00F5_01C889DF.5E1313C0
Content-Type: text/html;
charset="us-ascii"
Content-Transfer-Encoding: quoted-printable