--===============58955954119084542==
Content-Type: multipart/alternative;
boundary="-----------------------------1118844925"
-------------------------------1118844925
Content-Type: text/plain; charset="US-ASCII"
Content-Transfer-Encoding: 7bit
Don,
I measured the rod last night and found the taper to be a little difficult
since some flats were as much as .007 larger than the other two. I used the one
from the two flats. I also have the guide spacing listed. I measured the
entire rod since I was doing this.
This is measured OVER the varnish that I put on the rod. I would guess .004
thick.
0 = under tip top
2 = .082
5 = .091
10 = .106
15 = .115
20 = .133
25 = .146
30 = .160
35 = .173
---------------tip section
40 = .191
45 = .207
50 = .219
55 = .236
60 = .248
65 = .260
70 = .275
--------------Mid section
75 = .300
80 = .325
85 = .344
90 = .360
95 = .372
98 = .376
Grip and reel seat are 10 inches long
Guide spacing was measured from the tip top and I may have altered this when
I refinished the rod since there are more guides than I believe the original
had..
1 = 4 3/4
2 = 9 5/8
3 = 13 5/8
4 = 22
5 = 29 3/4
6 = 39 1/4
7 = 51 3/4
8 = 65 3/4
stripper 78
email:
Office 630-960-0100 X307
cell 630-347-3568
-------------------------------1118844925
Content-Type: text/html; charset="US-ASCII"
Content-Transfer-Encoding: quoted-printable
Don,
I measured the rod last night and found the taper to be a little diffic=
ult since some flats were as much as .007 larger than the other two. I used=20=
the one from the two flats. I also have the guide spacing listed. I measured=
the entire rod since I was doing this.
This is measured OVER the varnish that I put on the rod. I would guess=20=
.004 thick.
0 =3D under tip top
2 =3D .082
5 =3D .091
10 =3D .106
15 =3D .115
20 =3D .133
25 =3D .146
30 =3D .160
35 =3D .173
---------------tip section
40 =3D .191
45 =3D .207
50 =3D .219
55 =3D .236
60 =3D .248
65 =3D .260
70 =3D .275
--------------Mid section
75 =3D .300
80 =3D .325
85 =3D .344
90 =3D .360
95 =3D .372
98 =3D .376
Grip and reel seat are 10 inches long
Guide spacing was measured from the tip top and I may have altered this=
when I refinished the rod since there are more guides than I believe the or=
iginal had..
1 =3D 4 3/4
2 =3D 9 5/8
3 =3D 13 5/8
4 =3D 22
5 =3D 29 3/4
6 =3D 39 1/4
7 =3D 51 3/4
8 =3D 65 3/4
stripper 78
email:
Office 630-960-0100 X307
cell 630-347-356=
8
-------------------------------1118844925--
--===============58955954119084542==
Content-Type: text/plain; charset="us-ascii"
MIME-Version: 1.0
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
RODMAKERS mailing list
http://smtp.goldrush.com/mailman/listinfo/rodmakers
--===============58955954119084542==--